我們是專業的強鹿柴油機活塞組件的拆卸技術方法供應服務商.我們可提供強鹿柴油機活塞組件的拆卸技術方法銷售維修保養零配件服務.強鹿柴油機活塞組件的拆卸技術方法想要更多的類型，請現在聯系湖南英珀威機械有限公司！
首頁
產品展示>強鹿柴油機活塞組件的拆卸技術方法與測量標準參數值
產品中心
美國強鹿柴油機維修配件技術中心
約翰迪爾John Deere柴油機配件 美國麥克福斯
卡特彼勒柴油發動機參數
沃爾沃發動機全系參數
英國珀金斯原廠配件
珀金斯柴油機技術中心
珀金斯發動機零件查詢圖冊
日本三菱柴油機發電機配件
德國道依茨 韓國大宇柴油發動機配件
康明斯全系列柴油發動機
沃爾沃 MTU 原廠配件銷售中心
瑞典沃爾沃遍達原裝柴油機配件
康明斯維修技術中心
卡特彼勒柴油發動機原廠配件銷售中心
品牌柴油發電機組
康明斯柴油發動機配件中心
強鹿柴油機活塞組件的拆卸技術方法與測量標準參數值
詳細描述
強鹿柴油機活塞組件的拆卸技術方法
1. Remove piston rings using the JDE135 (shown),JDE85, or KJD10140 Piston Ring Expander.
2. Remove and discard piston pin snap rings.
3. Separate piston and rod. Keep these parts in placewith their respective cylinder liner.
John Deere約翰迪爾強鹿柴油機活塞環槽磨損的檢查與標準值參數
Pistons with tapered rods will use JDE62 Ring Groove Wear Gauge and pistons with straight rods will use JDG957 Ring Groove Wear Gauge.
1. Use the appropriate ring groove wear gauge (C) to check wear of keystone ring groove (top groove). Check grooves at several locations around the circumference of piston. Gauge shoulders should not contact ring land. Clearance (D) between shoulders of tool and ring land indicate ring groove is good. If ring groove is worn, replace piston and liner as a matched set. If ring groove is good, proceed to next step.
A—Piston with Good Keystone Ring Groove
B—Piston with Worn Keystone Ring Groove
C—Ring Groove Wear Gauge
D—Clearance (Normal)
E—No Clearance (Replace)
2. Check second (Compression) ring groove using new piston ring and a feeler gauge. Measure clearance at several points. Compare measurements with specifications.
3. Check third (Oil Control) ring groove using proper new piston ring and a feeler gauge. Measure clearance at several points. Compare measurements with specifications.
Specification
Piston Ring-to-Groove
Clearance—New Piston Ring
(Second Compression Ring
Groove)—Maximum Clearance.................................. 0.20 mm (0.008 in.)
Piston Ring-to-Groove
Clearance—New Piston Ring
(Third Oil Control Ring Groove,
Standard Ring)—Maximum
Clearance ................................................................... 0.82 mm (0.032 in.)
Piston Ring-to-Groove
Clearance—New Piston Ring
(Third Oil Control Ring Groove,
Heavy Duty Ring)—Maximum
Clearance ................................................................... 0.15 mm (0.006 in.)
4. Replace piston and liner (as a set) if clearance exceeds specification.
John Deere約翰迪爾強鹿柴油機活塞銷孔的測量與標準值參數
Measure piston pin bore. If bore is not within specification, replace piston and liner set.
Specification
Piston Pin Bore (Small Pin)—ID 34.935—34.945 mm (1.3754—1.3758 in.)
Piston Pin Bore (Large Pin)—ID 41.285—41.295 mm(1.6254—1.6258 in.)
活塞裙的測量與標準值參數
1. Measure piston skirt (A) 90° to piston pin bore and 28 mm (1.1 in.) from bottom of piston (B). Record measurement.
Specification
Piston Skirt (Measurement Taken at Bottom of Skirt 28 mm [1.1 in.]
from Bottom of Piston)—Diameter 106.38—106.40 mm (4.188—4.189 in.)
2. Measure cylinder liner as directed later in this groupand compare with piston measurement.
活塞的高度的測量與標準值參數
Measure piston height from center of piston pinbore-to-top of piston.
Piston (Two Valve Head Engines)—Specification
Piston—Height (Measured fromCenter of Pin Bore to Top ofPiston) 71.64—71.70 mm (2.820—2.823 in.)
Piston (Four Valve Head Engines)—Specification
Piston—Height (Measured fromCenter of Pin Bore to Top ofPiston) 71.60—71.65 mm(2.819—2.820 in.)